Edmonton Electrician | What to Know When Buying Motion Detectors

780-935-0622

Contact Info

Our Office

14927-69ST NW
T5C-0J3
Edmonton, Alberta

}

Regular Hours

M-F: 7am – 4:30pm
Evenings, Weekends & Holidays by appointment.

r

Emergency Service

24/7/365
Emergency fees apply
v

Get in Touch

info@hauerpower.ca
(780) 935-0622

Edmonton Electrician | What to Know When Buying Motion Detectors

one of the most common phone calls that Edmonton electrician gets is from people who have recently bought a new house business and they believe that the motion detectors do not work. They asked for the professionals to come out and remove the old and non-functioning motion detector, and install a new system. However, people need to take into consideration that not all motion detectors that are not currently functioning need to be replaced. They said that there’s several things that people should be doing that’s going to allow them to ensure that the their motion sensors in good working order they don’t have to face them very often.

It’s very important that people understand that they should be cleaning their motion sensors at least every two to three months. This is true whether they are inside or outside motion detectors does Edmonton electrician. In fact, the inside motion detectors often get covered in dust that affect how useful they are. As well, people need to understand that different aspects of the weather, whether it is raining, snowing or even wind that’s blowing dirt, grits and debris all over the sensors, this dirt and end up impeding the sensors abilities to do their job. Therefore, people should first get a non-abrasive cleaner out of microfiber cloth and clean the sensors every few months. If there has been a lot of rain, snow, or winds, then people may want to clean even more often than that.

the next thing that people should take into consideration, is that they should be testing their motion sensors on a monthly basis. Edmonton electrician recommends that people start out a time every month that they get out and test the functionality of their motion detector. This way, they can figure out if a motion detector is stopping working slowly, or if there’s something else that the electrician can do that will make sure that it’s in good operating order. The worst thing would be for a person to not check their motion detectors at all, and find out the hard way that it’s not allowing the light come on, either to keep things safe for their family, or to minimize crime in their area.

Something else that people should take into consideration, is if they think their motion detector is not functioning properly because it keeps coming on even if there’s no one there to strike that might not be because it’s broken. Edmonton electrician because the sensors are passive infrared radiation sensors, they can actually be interrupted by electrical ignore. And electricity providers have started putting Wireless signals on to their power metres, that they don’t have to send out someone to check Kneaders individually, they can read them from anywhere they want. Therefore, these Wireless signals and interrupt the signal to the motion detector, causing it to go off even when there’s nobody there.

Edmonton electrician wants to ensure that everybody gets to save as much money as possible, and doesn’t want to replace a completely functional motion detector system. Therefore, by figuring out if it’s a false correction that needs fixing, or a motion sensor that needs to be cleaned. Doing these things can help ensure that people have working motion sensors, without necessarily having to buy a brand new one

Edmonton Electrician | What to Know When Buying Motion Detectors

it’s very important that people are taking into consideration what they are buying their motion detectors for does Edmonton electrician. the reason is because there’s a variety of different motion detectors that are available on the market, and they shoot a variety of purposes. Therefore, they need to take into consideration if it is going to be an internal motion sensor or an external motion sensor. And if it’s going to be a Residential motion sensor, or if it’s for a business owner in there commercial or industrial complex.

When people are taking into consideration this, people should ensure that there are a variety of sensitivity settings or these variety of different applications. Ultimately, Edmonton electrician would say that residential should have the lowest sensitivity settings set. Meanwhile commercial and Industrial applications to have the highest sensitivity set. There is a wide variety of reasons for this, but ultimately it comes down to safety.

For example, residential areas have a lot more ambient light than commercial or industrial complexes. Because of that, people need to be mindful that they are not upsetting their neighbours by Shining Light into their home at all hours of the night. Edmonton electrician does their best aim light bulbs and fixtures away from Neighbors, but it still can be seen Ama SO2 turn the sensitivity settings down, means that it provides the least amount of nuisance to Neighbors.

Another reason why residential areas that have the lowest sensitivity settings, and it’s to provide safety to drivers in the area says Edmonton electrician. The reason why it’s a safety issue, is if the sensitivity is turned all the way up, and a car driving by triggers the motion detector, it could very easily by the light as they’re driving by. Therefore, residential areas should always have sensitivity settings that very low.

Internal residential also need to have the sensitivity on low says Edmonton electrician. The reason is that people inside the house don’t get blinded when the lights come on very abruptly. Whether it’s a hallway sensor to light the way for people walking down the hallway at night, kitchens and Sir that allows people to see the kitchen when they come into it at night. Or even almost most importantly a bathroom sensor, that can light up the bathroom When someone enters. I having these steps to a low sensitivity, it meant of mises the chances of people being blinded in their home as they make their way from room to room in the dark.

Therefore, people need to take several things into consideration when they are getting motion detectors set up whether it’s for their own, internal, external or if it’s for their business whether it’s internal or external. Understanding the different applications can help people understand how to choose the best one.

Contact Us

14927 69 St NW, Edmonton, AB T5C 0J3